Asmb Worker Structures

Standard Job Description

Builds and/or mates structures where the assembly is coordinated, or built with the benefit of tooling with established primary locations, and as necessary, lays out and locates rivet, bolt and fastener hole patterns, trim lines, and parts from established locations by simple measurement. Works the assembly in proper sequence, loads jig, and does necessary work and/or rework to complete the assembly, either in or after removal from jig.

Performs such operations as minor reforming of parts to correct contour; crimping, trimming and filing parts to fit; framing, skinning, riveting; attaching fittings and installations required to obtain a finished assembly. Drills and reams to specified (not "exacting") tolerances. Mills rivets as required. May improvise shop aids to facilitate assembly and installation.

Performs any type of routine or repetitive installation work involving bolting, screwing, clipping or riveting, in attaching or locating electrical, hydraulic, plumbing or mechanical units, parts, assemblies or equipment where their location is determined by pilot holes, back drilling, templates, previously punched or drilled holes, and as necessary, lays out by simple measurement from specific reference points such as edge, located holes, ribs, stringers, or other installed units. Torques and/or safeties bolts as required. When required by practical assembly sequence, installs incidential plumbing, electrical rigging or other functional items.

Installs under conditions described above, such typical items as: (1) Braces, brackets, platenuts, and clips for fastening, hanging, or supporting installations; (2) conduit, junction boxes; instrument panels; wire harnesses completely assembled, or single wires, requiring cutting, lugging, forming, trying, but not requiring soldering; (3) tubing for hydraulic, plumbing, and air conditioning systems; (4) cables, drums, pulley assemblies, push pull rods, and linkage, etc; (5) mechanical units such as tracks, hinges, up locks, down locks, etc.; (6) sealing compounds, insulation, rubber, felt, gaskets, or other material to aircraft parts; (7) floor supports, floor boards, stands, and similar items; (8) bonding, but does not perform bonding checking operations; (9) miscellaneous items such as fuel and oil tanks, cabinets, partitions, seats, metal molding, aircraft hardware, oxygen bottles, water breakers, alcohol units, storage equipment, etc.

Disassembles and/or reassembles structure and installations where units are essentially returned to their original position, or where their position previously has been established. May improvise shop aid to facilitate assembly and installation.

Fabricates structural items, such as clips, angles, gussets, and patches, etc.

To apply an elementary knowledge of aircraft assembly, structures assembly and installation practice and procedure. To apply an elementary knowledge of the working characteristics of aircraft materials. To use necessary jigs, fixtures, rivet upsetting, assembly equipment, and hand tools. To read and interpret detail, assembly and installation blueprints, or other authorized documents to obtain structure assembly and installation information and material callouts. To use applicable measuring devices. To use arithmetic through decimals and fractions. To work to tolerances as required for the type of work described herein. To make repairs from authorized repair manuals, or other authorized documents.
**SEE COMPLETE JOB DESCRIPTION

At the start of employment, you will be required to attend a skills training program, and take and pass a performance demonstration test following completion.

GAhourly

Basic Qualifications

Note to hourly employees at Aeronautics, Marietta: You are not eligible to apply via the LMCareers talent gateway for any positions that are included in your current bargaining unit (union).

Two years of aircraft sheet metal assembly (riveted structure and installation of functional and/or electrical components) experience or equivalent training. This should include the ability to drill and rivet thin sheet metal and the ability to read and use aircraft detail and assembly blueprints.

OR

Candidates with a completed Airframe & Powerplant (A&P) Licenses acquired through completion of accredited courses of study from aeronautical technical institutions with course curriculums such as Pittsburgh Institute of Aeronautics, Spartan School of Aeronautics, Embry Riddle, and Aviation Institute of Maintenance of Duluth.

At the start of employment, you will be required to attend a skills training program, and take and pass a performance demonstration test following completion.

Desired Skills

Aerospace and Defense structural assembly experience

* Basic to Advanced Blue Print Reading
* Use of drill blocks
* Drill holes through thick materials

Pay Information

• $18.10 - $38.71

At Lockheed Martin, we know mission success starts with taking care of our people. Our Total Rewards program is designed to attract top talent, support your well-being, and help you grow—both professionally and personally.

The salary range for this position is as listed on the requisition. Please note that the salary information listed is a general guideline only.
Lockheed Martin considers factors such as (but not limited to) scope and responsibilities of the position, candidate's work experience, education/ training, key skills as well as market(work location) and business considerations when extending an offer.

Benefits offered: Medical, Dental, Vision, Flexible work arrangements and schedules (e.g., 4x10), 401(k) match, Paid time off, Holidays, Parental Leave, EAP, Flexible Spending Accounts, Education Assistance, Life Insurance, Short-Term Disability, and Long-Term Disability.

• Additional specific benefits are dependent upon the business unit and the collective-bargaining agreement.
• Annual short-term and/or long-term incentive compensation programs may be offered depending on the position. Payments under these annual programs are not guaranteed and can vary from year to year and are tied to a range of performance metrics.
• For (Washington state applicants only) Represented full time employees accrue 6.67 hours of Vacation per month; accrue up to 52 hours of sick leave annually; receive at least 96 hours for holidays. PTO, Vacation, sick leave, and holiday hours are prorated based on start date during the calendar year.